and comparatively high strength. It has a very good surface finish that is far superior to hot rolled A36. ASTM A366 (alloy 1008) steel Ultimate Tensile Strength, psi 43,900 - 51,900 Yield Strength, psi 26,100 - 34,800 Minimum Properties Elongation 42 - 48% Iron (Fe) 99% Carbon (C) 0.08% Manganese (Mn) 0.6% max Phosphorus (P) 0.035% max
AISI 1008 Steel, CQ, DQ, and DQSK sheet, 1.6-5.8 mm thickTensile Strength, Ultimate; Tensile Strength, Yield; Elongation at Break, in 50 mm. Modulus of Elasticity; Bulk Modulus, Typical for steel; Poissons Ratio, Typical For Steel; Machinability, Based on AISI 1212 steel. as 100% machinability. Group I bar, rod, and wire products machinability can be improved by cold drawing. Shear Modulus, Typical
ASTM A1008 Steel. Cold-rolled, carbon, structural, high-strength low-alloy, high-strength low-alloy with improved formability, solution hardened, and bake hardenable steel sheet, in coils and cut lengths. ASTM 1008 is a low-carbon steel containing approximately 0.40% manganese that has excellent weldability and formability, primarily used in extruded, cold headed, cold upset, and cold pressed parts and forms.
ASTM A366 1008 AISI1008 SAE1008 Steel - SAE AISI 1010 It is known for its very good formability and comparatively high strength. It has a very good surface finish that is far superior to hot rolled A36. 1008 Steel is an economical, general purpose steel grade offering moderate strength and toughness. As a standard grade, 1008 steel is
ASTM A510 1008 ASTM A510/A510M - BBN STEEL STORESASTM A510 1008 ASTM A510/A510M Material, A510 1008 steel,A510 1008 steel hardness, A510 1008 plate weight , A510 1008 plate size, A510 1008 plate thickness, ASTM A510 1008 ASTM A510/A510M tensile strength, yield strength . Yield R p0.2 (MPa) Tensile R m (MPa) Impact KV/Ku (J) Elongation A (%) Reduction in cross section on fracture
ASTM A366 (alloy 1008) steel ; Minimum Properties:Ultimate Tensile Strength, psi:43,900 - 51,900:Yield Strength, psi:26,100 - 34,800:Elongation:42 - 48%:Chemistry:Iron (Fe) 99%:Carbon (C) 0.08%:Manganese (Mn) 0.6% max:Phosphorus (P) 0.035% max:Copper (Cu) 0.2% min:Sulfur (S) 0.04%
Cold Rolled 1008 Steel Sheet - Cold Rolled Steel Sheet 1008 Cold Rolled Steel is a standard grade Carbon Steel. This alloy is generally used for "commercial quality" cold rolled steel sheet. It is an economical, general purpose steel grade offering moderate strength and toughness. As a standard grade, 1008 steel is used in many common, low-stress applications. Weldability (spot, projection, butt, and fusion) and brazeability are excellent.
HSLA Greer SteelHow do these properties compare to conventional materials? The table below shows the typical values for both 1008/1010 in various temper ranges and annealed and full hard 1050. Grade:1008/1010 5 temper:1008/1010 3 temper:1008/1010 1 temper:1050 Annealed:1050 Full Hard:Yield:24-35 ksi:35-45 ksi:64-84 ksi:43-55 ksi:100-110 ksi:Tensile:38-50 ksi:45-65 ksi
SAE-AISI 1008 steel is a carbon (non-alloy) steel formulated for primary forming into wrought products. 1008 is the designation in both the SAE and AISI systems for this material. G10080 is the UNS number. It has the highest thermal conductivity among wrought carbon or non-alloy steels.
SAEJ 403 1008,SAEJ 403 1008 steel Shanghai Royal IndustrySAEJ 403 1008 typical tensile strength varies between 276 and 1882 MPa. The wide range of ultimate tensile strength is largely due to different heat treatment conditions of SAEJ 403 1008. SAEJ 403 1008 steel plate high carbon steel 1008 steel plate, SAEJ 403 1008 steel plate, we can regard 1008 steel plate as high carbon steel.
Spartan:A710, Navy HSLA-80/100 and HPS 100W SteelsFigure 1:Yield Strength of Spartan Steels vs. Aging Temp. for 1-1/4" (32 mm) Thick Plates Figure 3:Influence of Carbon Level and Carbon Equivalent on Susceptibility to HAZ Cracking of Plate Steels (from Graville) Figure 2:CVN Toughness at -120°F (-84°C) for Spartan Steels vs. Aging Temp. for 1-1/4 (32 mm) Thick Plates Yield Strength